DIN Rail Power Supply by Sola/Hevi-Duty: SDN-C Next Generation DIN Rail Power Supplies

A printable version of the following sections is available by selecting the pdf file to the left.

Industrial Machine Control	Vending Machines
Process Control	Packaging Equipment
Material Handling	Amusement Park Equipment
Conveying Equipment	Semiconductor Fabrication Equipment

Accessories

Description	Catalog Number
	SDN 5-24-100C	SDN 10-24-100C
Input
Nominal Voltage	115/230 Vac
-AC Range	85 - 264 Vac
-DC Range	90 - 375 Vdc
-Frequency	43-67 Hz, 400 Hz
Nominal Current¹	1.65 - 0.55 A	3.2 - 1.0 A
-Inrush current max.	Typ. < 15 A	Typ.< 30 A
Efficiency (Losses²)	> 90% typ. (12 W)	> 90% typ. (24 W)
Power Factor Correction	Active power factor correction to better than 0.92
Output
Nominal Voltage	24V (22.5-28.5 Vdc Adj.)
-Tolerance	< ±2 % overall (combination Line, load, time and temperature related changes)
Initial Voltage Setting	24.5V ± 1%
-Ripple⁴	< 50 mVpp
PARD	PARD (Periodic and Random Deviation) = 100 mV peak-peak max
Overvoltage Protection	> 30.5 but < 33 Vdc, auto recovery
Power Back Immunity	< 35V
Nominal Current	5 A (120 W)	10 A (240 W)
-Peak Current	1.5 × Nominal Current for 2 seconds minimum while holding voltage > 20 Vdc
-Short Curcuit Current	1.5 x Nominal Current at near zero volts at short circuit condition
-Current Limit	PowerBoost™
Parallel Operation	Switch selectable single unit or parallel unit operation. Units will not be damaged by parallel operation (regardless of switch position setting).
Holdup Time	>20 ms (Full load, 100 Vac Input @ Tamb=+25°C) to 95% output voltage
Voltage Fall Time	<150 mS from 95% to 10% rated voltage @ full load (Tamb=+25°C)
Line and Load Regulation	< 0.5%
General
EMI -Emissions	EN61000-6-2:2001, EN61000-6-3:2001, Class B EN55011, EN55022 Radiated and Conducted including Annex. A, EN61000-3-2
-Immunity	EN61000-6-1:2001, EN61000-6-2:2001, EN61000-4-2 Level 4, EN61000-4-3 Level 3, EN61000-4-6 Level 3, EN61000-4-4 Level 4 input and level 3 output. EN61000-4-5 Isolation class 4, EN61000-4-11, IEC 61000-4-34 voltage dip immunity standard
Approvals	UL508 Listed, cULus; UL 60950-1, cURus; IEC60950-1; UL60079-15 (pending) and IEC60079-15 (pending) CE (LVD 73/23 & 2004/108/EC), (EMC 89/336 & 93/68/EEC); EN61000-3-2
Temperature	Storage: -25 to + 85oC, Operation -10 to +60oC full power, with linear derating to half power from 60 to 70oC (Convection cooling, no forced air required). Operation up to 50% load permissable with sideways or front side up mounting orientation.
MTBF Standard⁶	> 650,000 hrs	> 550,000 hrs
Warranty	5 Years
General Protections/ Safety	Protected against continuous short -circuit, continuous overload, continuous open circuit. Protection Class 1 (IEC536), degree of protection IP20 (IEC60529) Safe low voltage: SELV (acc. IEC60950-1)
Status Indicators	Visual: 3 status LEDs (Input, Output, Alarm) Relay: N.O. contact rated 200ma/50 Vdc
Installation
Fusing
-Input	Internally fused
-Output	Outputs are capable of providing high currents for short periods of time for inductive load startup or switching. Fusing may be required for wire/loads if 2x Nominal O/P current rating cannot be tolerated. Continuous current overload allows for reliable fuse tripping.
Mounting	Simple snap-on to DIN TS35/7.5 or TS35/15 rail system.
Connections	Input: Screw terminals, connector size range: 16-10 AWG (1.5-6 mm2) for solid conductors. Output: Two terminals per output, connector size range: 16-10 AWG (1.5-6 mm2) for solid conductors.
Case	Fully enclosed metal housing with fine ventilation grid to keep out small parts.
-Free Space	15 mm in front, 25 mm above and below, 10 mm left and right.
H x W x D (inches/mm)	4.88 in. × 1.97 in. × 4.55 in. (124 mm × 50 mm × 116 mm)	4.88 in. × 2.36 in. × 4.55 in. (124 mm × 60 mm × 116 mm)
Weight (lbs/g)	1.5 lbs (620 g)	2.2 lbs (1100 g)
Notes: 1. Not UL listed for DC input. 2. Input current ratings are conservatively specified with low input, worst case efficiency and power factor. 3. Losses are heat dissipation in watts at full load, nominal input line. 4. Ripple/noise is stated as typical values when measured with a 20 MHz, bandwidth scope and 50 Ohm resistor. 5. Peak current is calculated at 24 Volt levels. 6. MTBF 115 Vac (@ 120 watts & 240 watts) at 25oC ambient per Telecordia Issue 1.